徹底弄明白HFSS端口激勵的區別 Lumped port、wave port

2016-11-03  by:CAE仿真在線  來源:互聯網

lumped ed port=> the excitation is applied at a point/cell, as a voltage or current. 

lumped port的激勵以電壓或電流的形式,加在一個點或單元上。  

wave-port=> the excitation is so-called eigen(本征)-wave, such as the quasi-tem wave supported by a microstrip line. It applies over a cross-sectional area.   

而wave-port的激勵稱做本征波,比如微帶線饋源提供的準TEM波,它加在一個橫截面(傳輸線的橫剖面)上。

voltage is scalar, wave is vector by nature, hence there are substantial difference between the two. 

So use waveport whenever possible, because "simulation of wave phenomenon" is what HFSS is designed for. And compare with the "correct" measurement whenever possible (i.e. measure "wave", not simply "voltage").

電壓是標量,而波本質上是矢量,因此兩者間有很大區別。當情況允許時,盡可能選擇wave port

這是由于HFSS是為“波仿真”設計的,相對于簡單的“電壓”,測量“波”可使結果更精確。

Why lumped port is there? It is easy to applied and people found that good/reasonable results can be obtained. 

Why? if the frequency is low enough or the excitation is applied at sufficiently small area, then the "wave" can be described by some "voltage" or "current", which must be "measured"/"calculated"/de-embedded/etc in the correct manner.  

那為什么還要使用lumped port呢,這是由于lumped port激勵的添加簡單,并且可獲得良好的結果。如果頻率很低或者激勵加在足夠小的區域上,“波”就可以用“電壓”或“電流”來描述,必須用正確地方式測量、計算。

if the excitation can be applied on some locally uniform region=>waveport, if geometry/material discontinuities are near/closer to the point of excitation=>lumped ed port might be the only way.   

另外,如果激勵可以加在某些局部均勻分布的區域,應該采用waveport,如果激勵點附近存在幾何或材料上的不連續區,lumped port可能就是唯一選擇了。 



開放分享:優質有限元技術文章,助你自學成才

相關標簽搜索:徹底弄明白HFSS端口激勵的區別 Lumped port、wave port 徹底弄明白HFSS端口激勵的區別 Lumped port、wave port HFSS電磁分析培訓 HFSS培訓課程 HFSS技術教程 HFSS無線電仿真 HFSS電磁場仿真 HFSS學習 HFSS視頻教程 天線基礎知識 

編輯
在線報名:
  • 客服在線請直接聯系我們的客服,您也可以通過下面的方式進行在線報名,我們會及時給您回復電話,謝謝!
驗證碼

全國服務熱線

1358-032-9919

廣州公司:
廣州市環市中路306號金鷹大廈3800
電話:13580329919
          135-8032-9919
培訓QQ咨詢:點擊咨詢 點擊咨詢
項目QQ咨詢:點擊咨詢
email:kf@1cae.com